One of my friend went for a VM with a German hosting provider. He got single IPv4 (quite common) and a /64 IPv6. Overall /64 per VM/end server used to be ok till few years back but now these days running applications inside LXC containers (OS level virtualization) make more sense. This gives option to maintain separate hosting environment for each application. I personally do that a lot and infect blog which you are reading right now itself is on a LXC container.

 

So my friend tried to do similar setup but it went tricky for him because of just one single /64 from upstream. For me I have a /32 and I originate a /48 from this location giving me over 65k /64s of IPv6 for any testing and random fun application deployments.

 

The challenge in his setup was following: 

1. One can use available 18 quintillion IPv6 address in the /64 by bridging the internal container interface with it. That’s ok for IPv6 but fails terribly for IPv4 as many people do not need dedicated IPv4 per container while it’s fun to have that for IPv6 and gives so much flexibility. For IPv4 a custom setup makes more sense with specific DST NAT and reverse proxy for port 80 and port 443 traffic.
2. For NATing IPv4 a separate virtual interface (veth) makes sense so that one can run private IPv4 addressing. Now here firstly subnetting of /64 sounds stupid and weird but even if one does that it won’t work because main /64 allocation is via layer 2 and not a routed pool. This doesn’t works, read further on why.

 

So after our discussion my friend decided to use a /112 for container (ugly I know but datacenter provider quoted 4-5Euro/month for additional /64!). A /112 out of 128 IPv6 addressing gives one 2^16 i.e 65k IPv6 addresses to use on containers which is good number of IPv6 with few limitations like:

1. Many things support /64 only like for instance use of IPv6 in OpenVPN sticks with that due to Linux Kernel implentation.
2. IPv6 auto conf heavily depends on it. In my own personal setup I have a dedicated /64 for the container interfaces and radvd takes care of autoconfig via router advertisements. With anything less then /64 that’s not possible.

 

So we broke the allocated /64 into a /112 and allocated first IP our of that on veth based interface and next used 2nd IP on a container. IPv4 was working fine on container with SRC NAT in this case but IPv6 connectivity wasn’t. Container was able to reach host machine but nothing beyond that. I realised issue was of layer 2 based allocation which was relying on IPv6 NDP. So the container’s IPv6 had internal reachability with host machine but whenever any packet came from internet, the L3 device of VM provider wasn’t able to send packets further because of missing entry of that IP in their NDP table. Problem wasn’t just with IPv6 of container but with just any IPv6 used on any interface of the VM (whether that virtual veth or even loopback). Adding IPv6 on eth0 (which was connected to upstream device) was making IPv6 to work but not possible to use it further on a downstream device like a container. The datacenter provider offered to split /64 into /65s and route 2nd /65 for a monthly charge (ugly!!!). So we ended up with a nasty workaround – use of proxy NDP. This is very similar concept to proxy arp as in case of  IPv4. So that required enabling proxy arp by enabling in sysctl.conf and next doing proxy NDP for specific IPv6 using: ip neigh add proxy xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx/64 dev eth0

 

 

This works and thus with an extra step of adding proxy NDP entry for each IPv6 in use. In general routed pool is way better and if I had a make a choice on behalf of his datacenter provider, I would have gone for use of /64 for point to point connectivity and a routed /48. At Hurricane Electric (company I work for) we offer IPv6 free of charge so that networks can grow without having to worry about address space or do nasty things like one I described above. 😉

Haven’t deployed IPv6 on your application yet? Do it now!

Time to get back to work and do more IPv6 🙂